Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Kent?
Gate parts and welding in Kent typically run $180 to $650 for common repairs, with most residential jobs landing in the $250 to $400 range and commercial swing or slide gates climbing toward $900 or more when heavy hardware and operator work are involved. A single replacement part like a roller, hinge, or sensor might cost $95 to $220 installed, while welded frame and post repairs generally fall between $200 and $700 depending on access and material. Every price is set per job, and the written estimate you get after we look at the gate is the number that stands.
We’re gate specialists, not generalists. Every job we take is a gate job, which is why we can give you a straight answer on parts and welding costs instead of guessing at what a general handyman would charge. Call (855) 360-7358 for a free estimate. We answer 24/7.
Key Takeaways
- Most residential gate parts and welding jobs in Kent fall between $180 and $650.
- Commercial gates with heavy frames, operator mounts, and crash bars run higher, often $500 to $1,400.
- Parts availability drives a lot of the cost: residential brands like Ghost Controls and Mighty Mule are quick to source; commercial DoorKing and BFT components can add time.
- Free estimates, upfront pricing, and a satisfaction guarantee mean you know the number before any welding starts.
- We work on the brand already on your property, whether it’s LiftMaster, FAAC, Linear, or Viking.
Gate Parts & Welding Cost Breakdown (2026)
Here’s how the common parts and welding jobs break down for the Kent market. Ranges reflect typical residential and light commercial work. Heavy commercial gates and older systems needing custom fabrication sit at the top of each range or above it.
| Job Type | Typical Cost Range | What It Covers |
|---|---|---|
| Roller or hinge replacement | $95 – $220 per point | New hardware, alignment, and function check |
| Gate latch or catch replacement | $120 – $260 | Latch, strike, and adjustment |
| Safety sensor or photo-eye replacement | $150 – $320 | New sensor pair and re-aiming |
| Operator gear or sprocket replacement | $220 – $540 | Part plus labor to reset the drive |
| Hinge-post or frame weld repair | $200 – $700 | Cut, weld, grind, prime, and finish |
| Track or guide-rail straightening | $240 – $600 | Realignment, welding, and resetting the gate |
| Drop-rod or stop repair | $140 – $340 | Hardware and welding where needed |
| Full welding rebuild (post, frame, hinge plates) | $600 – $1,400 | Multi-point welding and realignment |
| Commercial operator mount welding | $400 – $1,100 | Reinforced bracket, welding, and torque setup |
| Custom bracket fabrication | $180 – $520 | Made-to-fit bracket for hard-to-source parts |
What pushes cost up: heavy gauge steel and commercial hinge plates take more time to weld and finish. Gaining access around mature landscaping or a tight driveway corner costs labor hours. Rare parts for older commercial operators can add days to the job while we source them. What pulls cost down: a single point of repair, easy access, and hardware that’s common to the brand on your gate. Because we work across nine brand families, from residential-grade Mighty Mule to commercial-grade FAAC, we know which parts are quick and which take sourcing.
For a broader picture of what repair work looks like on a Kent gate, see our gate repair in Kent service.
What Affects Gate Parts & Welding Pricing in Kent
Kent weather, lot size, and gate type all move the number. Here’s what we factor into every estimate.
- Gate type and weight. A light residential swing gate with Mighty Mule automation takes a fraction of the time that a commercial slide gate with a DoorKing operator does. Heavier panels mean heavier hinge plates, more welding, and more labor to realign. Kent properties with long driveways and larger gates lean toward the higher end of the range.
- Brand and parts availability. We work on the brand already on your property, and that matters for cost. Parts for LiftMaster and Linear operators are usually quick to source. BFT, FAAC, and DoorKing commercial components sometimes take longer, and that sourcing time shows up in the overall job price.
- Welding scope and finish. A single hinge-post touch-up is one price; a rebuild across multiple weld points is another. Add priming and paint and the job grows. Rusted or previously welded frames take extra time to prepare before any new weld will hold, which is common on gates that have seen several rainy seasons in western Washington.
- Access to the work area. Welding equipment needs room. Gates boxed in by shrubs, retaining walls, or tight property lines take more setup time, and that setup is labor. A clear approach to the gate cuts the estimate.
- Manual versus automated. On an automated gate, welding near the operator requires extra care to protect the electronics and wiring. We isolate and test the operator before and after any heat work, and that protection step is part of the labor.
- Residential or commercial grade. Commercial properties, HOAs, and gated communities in Kent often need heavier hardware, stronger weld joints, and safety compliance checks. All of that adds to the job, but it’s also what keeps the gate in reliable service.
How to Save on Gate Parts & Welding
You don’t need to spend top dollar to get a gate back in service. A few practical steps shave cost without cutting corners on safety.
- Get a written estimate before work starts. A free estimate is the single best way to avoid surprise costs. We price the whole job in writing, so you know the number before any welding or parts ordering. Call (855) 360-7358.
- Fix the small parts early. A worn roller or hinge left alone can lead to frame damage and a much larger welding bill. Replacing a $95 to $220 part now can prevent a $600 to $1,400 rebuild later.
- Bundle related repairs. If your gate needs a hinge replaced and a frame touch-up, doing both in one visit saves labor compared to two separate trips. Tell us everything you’ve noticed when you call.
- Keep the gate clear of vegetation. Vines and shrubs holding moisture against the steel frame speed up rust, and rust means more welding. Trimming back growth protects the finish and lowers future repair costs.
- Match parts to the operator you already own. We source parts for the brand on your gate, which keeps you from paying for an unnecessary conversion. Whether it’s a Ghost Controls residential system or a Viking commercial operator, working with what’s installed is usually cheaper than switching.
Why Gate-Specific Expertise Keeps the Cost Down
A gate is a mechanical and electrical system, and a parts-and-welding repair done by someone who doesn’t know gate geometry, operator torque, or hinge load almost always costs more in the long run. We see this regularly around Kent: a generalist welds a hinge plate back on without accounting for the operator’s force settings, the gate binds, the motor strains, and the homeowner winds up paying for a second repair on top of the first.
Our technicians have up to 12 years of experience, and they work on both residential automation brands and commercial-grade systems. That depth is why we can usually diagnose a gate on the first visit, order only the parts that are actually needed, and weld the repair to hold. From the motor to the hinge, we handle the whole system.
If you want to understand how our broader service works, our Kent service area page covers the full scope.
What a Typical Parts-and-Welding Visit Looks Like
When you call, we ask what the gate is doing: sagging, dragging, catching, refusing to latch, or making noise. From there, we book a time, and a technician inspects the gate on-site. That inspection identifies which parts are worn and whether the frame or hinge posts need welding. You get a written estimate covering the parts, the welding, and any operator work, and nothing moves forward until you approve it. Then the technician completes the repair and tests the gate through a full cycle to confirm it’s back in service.
FAQs – Gate Parts & Welding Cost
How much does gate parts and welding cost in Kent?
Most residential gate parts and welding jobs in Kent cost $180 to $650, and commercial work on heavy swing or slide gates typically runs $500 to $1,400. A single part like a roller or latch installed lands around $95 to $260, while a multi-point weld rebuild can reach $600 to $1,400. Call (855) 360-7358 for an exact quote – estimates are free.
Is it cheaper to repair or replace a gate?
Repair is almost always cheaper than replacement when the frame and operator are sound, and most Kent gate repairs land in the $180 to $650 range while a full replacement runs far higher. If the frame is bent beyond welding repair or the operator is at end of life, we’ll tell you straight. For the wider repair picture, see electric gate repair in Kent. Call (855) 360-7358 for a free estimate.
How much does a hinge or latch replacement cost in Kent?
A hinge or latch replacement in Kent typically costs $95 to $260 installed. Heavy commercial hardware sits at the top of that range. We work on the brand already on your property, so you’re paying for the part and labor, not a conversion. Call (855) 360-7358 for an exact quote.
Do you weld on automated gates?
Yes. We weld on automated gates and take care to protect the operator’s electronics and wiring during heat work. Welding on a gate with a live operator is not a DIY job, since the power and force settings can cause serious injury if mishandled. Our technicians handle the isolation, the welding, and the operator test. Call (855) 360-7358.
Can you come today for a gate parts or welding problem?
Same-day service is often possible, with fast dispatch from 7am to 7pm. If your gate is stuck open or failing to latch, tell us when you call and we’ll get it booked. Call (855) 360-7358. We answer 24/7.
What Happens When You Call
You get a technician who works on gates every day, not a handyman squeezing it in between unrelated jobs. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’re licensed and insured, we give free estimates, and the price is set per job by the written estimate.
We handle gate installation as well as parts and welding, so if your gate is past repair, we can talk through replacement options rather than pushing you toward a second company. Commercial and residential, automated or manual, we work on the system that’s there.
Get a Free Gate Parts & Welding Estimate in Kent
If your gate is sagging, dragging, rusting at a hinge, or refusing to close all the way, the sooner it’s fixed, the less it costs. Give us a call and we’ll get a technician out to inspect the gate and give you a written estimate. Call (855) 360-7358 for a free estimate. We answer 24/7, fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Kent market as of 2026. Gate Repair Kent offers free estimates – call (855) 360-7358.
Written by the team at Gate Repair Kent.
What Our Customers Say
"Second time using them. Same guy, same good work."
- Eric Barrett"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Jennifer Whitaker"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Mark Norris