Gate Installation in Kent - Free Estimate, One Written Price

Trusted Gate Installation for Kent Homeowners

A gate that’s sized wrong, hung off level posts, or paired with an operator that can’t handle its weight will fight you from day one. That’s the problem we exist for. Our technicians have up to 12 years of experience working on gate systems, and every job we take is a gate job, not a side project between fence builds. Whether you’re replacing a sagging driveway gate in Kent or adding automation to a manual one, we measure the opening, match the operator to the panel weight, and quote the work before anything starts. Call (855) 360-7358. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.

Call (855) 360-7358

Automatic Gate Installation

Automatic Gate Installation means fitting a gate with an operator so it opens on a remote, keypad, or intercom signal instead of by hand. You need it when a manual gate has become a daily chore, when an HOA wants controlled entry, or when a new driveway layout calls for a barrier that opens for cars without anyone stepping out. We size the operator to the gate’s actual weight and swing or slide travel, install the safety edges and photo eyes, and run the low-voltage control wiring. You’ll see automated setups running on Mighty Mule or LiftMaster operators across Kent, and we work on either. Automatic Gate Installation typically runs $2,800-$7,500 depending on gate size, operator class, and site conditions; the written estimate sets the final price.

Operator Sizing and Travel

A swing operator rated for an 8-foot gate won’t last long on a 16-foot one, so we check panel weight and travel before we pick equipment. Getting this wrong is the most common reason a new automation feels sluggish within a year. We measure on site rather than trusting a rough dimension over the phone.

Safety Edges and Photo Eyes

Every automated gate we install gets obstruction detection on the closing path. Photo eyes catch a person or vehicle breaking the beam; safety edges reverse the gate on contact. These aren’t optional extras, and we won’t commission an automatic gate without them.

Gate Installation Services

Gate Installation Services cover the full job from setting posts to commissioning an operator, whether you’re starting from bare ground or replacing a gate that’s reached the end of its life. People call us for this when a gate has been hit by a vehicle, when wooden panels have rotted through, or when a property needs a barrier where there’s never been one. We handle residential and commercial work, so a single driveway in Kent and a controlled commercial entry both fall inside what we do. Installation pricing typically runs $1,800-$9,000 depending on gate type, width, material, and automation, and the written estimate sets the final price. We also fold in removal and disposal of the old gate when that’s part of the scope.

Removal and Site Prep

Old posts come out, the opening gets checked for level and square, and we confirm the ground will hold the new footings before anything is set. Skipping that check is how new gates end up dragging. Prep work is quoted up front with the rest of the job.

Manual and Automated Options

Not every gate needs an operator, and we’ll tell you when a manual swing gate is the right call for your traffic. When automation makes sense, we plan the control wiring and access method at the same time so it isn’t retrofitted later. Residential or commercial, automated or manual, the plan is set before we order anything.

Electric Gate Installation

Electric Gate Installation covers gates driven by a powered operator, including the motor, control board, power run, and access devices like keypads and remotes. You need this when a gate is too heavy to move by hand, when entry needs to be managed remotely, or when a property sees enough traffic that manual operation slows everyone down. This work sits where mechanical and electrical problem-solving meet, which is exactly why we keep it in-house. A common setup in Kent pairs a FAAC or Elite operator with a slide gate on a commercial entry, and we install and service both brands. Electric Gate Installation typically costs $3,000-$8,500 depending on operator class, gate weight, and the length of the power run. The written estimate sets the final price.

Power Runs and Control Wiring

We plan where power reaches the operator and how control wiring routes to keypads, intercoms, and loop detectors before installation begins. A tidy power run matters as much as the operator itself, because it’s what you’ll be living with for years. Any permit the city requires for that electrical work gets sorted before we start.

Access Control Integration

Keypads, remotes, and entry systems get wired and programmed so the gate responds to the right people and stays shut for everyone else. We test every access method at commissioning, not just the one remote in the box. If your property needs vehicle loop detection, that’s planned into the install.

Driveway Gate Installation

Driveway Gate Installation is the job of putting a gate across a vehicle entrance, sized to the driveway, matched to the property, and hung so it clears the ground through its full swing or slide. Homeowners in Kent call for it when a driveway is open to the street, when a new build needs a finished entrance, or when an old gate has finally given out. We survey the opening width, check slope and drainage, and pick a gate style that suits the house without overwhelming it. Driveway Gate Installation typically runs $2,200-$6,800 depending on width, material, and whether an operator is included. The written estimate sets the final price, and we quote before any work begins.

Measuring the Opening

Driveways are rarely perfectly flat or square, and a gate built to a nominal dimension will bind. We measure the actual opening and note the slope so the gate is built to fit what’s there. That step is why our installs run clean the first time.

Materials for the Northwest

Kent gets steady rain through the wet months, so we lean toward materials and finishes that hold up to damp rather than fighting it. Powder-coated steel and properly sealed wood both work; untreated softwood doesn’t. We’ll talk through the trade-offs before you commit.

Sliding Gate Installation

Sliding Gate Installation fits a gate that travels along a track or cantilever system instead of swinging open, which suits driveways where a swing would block a slope, a sidewalk, or a parked car. You need it when there’s no room for a swing arc, when wind catches a swinging panel, or when a wide opening needs a gate that clears fast. We set the track or cantilever frame, level the travel path, and confirm the gate rolls or slides without binding before the operator goes on. Sliding Gate Installation typically costs $2,600-$8,000 depending on width, operator, and whether a track or cantilever system is used. The written estimate sets the final price.

Track and Cantilever Choices

A ground track is simpler and cheaper, but it needs a clear path and collects debris if the driveway drains poorly. Cantilever systems cost more and free up the ground entirely. We match the choice to your site rather than defaulting to one.

Keeping the Gate on Its Path

Sliding gates that come off the track are a repair we see often, and the cause usually traces back to footings or alignment at installation. We check level along the full travel and set posts to proper footing depth. Getting that right at the start avoids the call later.

Gate Opener Installation

Gate Opener Installation is fitting a powered operator to a gate that already exists or is going in new, including the motor, control board, and the safety devices that make automation safe. Homeowners call for it when they want to stop getting out of the car in the rain, when a manual gate has gotten too heavy, or when an old operator has failed and replacement is the better move than repair. We check the gate’s weight, balance, and travel first, because a binding gate will burn out any operator you put on it. Gate Opener Installation typically runs $1,400-$4,200 depending on operator class, gate type, and wiring. The written estimate sets the final price, and we don’t start until you’ve agreed to it.

Checking the Gate Before the Operator

An operator can’t fix a gate that drags or sags, and fitting one to a binding gate just shortens its life. We test the gate’s movement by hand and correct hinge or track issues first. Only then does the motor go on.

Programming Remotes and Keypads

Once the operator is mounted, we program the remotes and keypads and walk you through operation before we leave. Travel limits and force settings get dialed in to the actual gate, not left at factory defaults. That’s the difference between a gate that runs smoothly for years and one that keeps stalling.

Gate Fabrication

Gate Fabrication is building a gate to fit an opening that stock sizes won’t cover, whether that’s an unusually wide driveway, a slope, or a design the property needs to match. It comes up when an off-the-shelf gate won’t clear the opening, when a property has a specific look to match, or when a commercial entry needs something heavier than a residential panel. We build to the measured opening, weld and finish to suit the material, and fit the hardware so the gate hangs true. Fabrication pricing typically runs $1,500-$7,000 depending on size, material, and design detail, with the written estimate setting the final price. Measuring happens on site before anything is built.

Building to the Opening

A gate fabricated to a nominal width is a gate that will need adjusting the day it’s hung. We take measurements from the actual opening, including slope and any obstruction, and build to those. That’s what keeps a custom gate closing cleanly for years.

Hardware and Finish

Hinges, latches, and stops get matched to the gate’s weight so nothing strains or sags. The finish is chosen for the material and the wet weather Kent sees, not just for looks. We won’t hand over a gate that isn’t hanging and latching correctly.

Brands We Service

We work on the brand already on your property, and that matters more than most people realize. Each operator line has its own control board, its own limit-setting quirks, and its own known wear points. We service LiftMaster operators and know how their control boards behave when they start faulting, and we work on FAAC systems well enough to tell an operator problem from a gate problem before parts get ordered. The same goes for Elite and Mighty Mule equipment across residential and commercial properties in Kent.

Our technicians have up to 12 years of experience across these systems, and we service equipment from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That range covers residential automation and commercial-grade access control without needing a second specialist. Whether you have LiftMaster or any other make, we can help.

Signs You Need a Pro Right Now

• The gate binds or drags through its travel. A gate that catches halfway through the swing or slide is putting strain on hinges, the track, or the operator every time it moves. Left alone, that strain turns a simple adjustment into a motor replacement.
• The operator hums but the gate doesn’t move. That usually points to a control board, capacitor, or mechanical fault inside the unit. It’s not something to diagnose by swapping parts, and it’s a sign the operator needs a trained eye.
• Safety edges or photo eyes aren’t stopping the gate. An automated gate that doesn’t reverse on obstruction is a genuine hazard to people and vehicles. Stop using it until it’s checked and repaired.
• Posts are leaning or the gate has dropped. A gate hanging off a leaning post puts load where it wasn’t designed to go. This one gets worse with every cycle and can bring the whole assembly down.
• You’re replacing a gate that failed suddenly. If a gate was hit, bent, or came off its track, don’t run the old operator on a new panel until the whole setup is checked. We’ll tell you what needs replacing and what doesn’t.

Our Process, Step by Step

1. 1
   Call and describe the job. We answer 24/7 and ask what the gate is doing, what kind of gate it is, and whether there’s an operator on it. That conversation tells us what to bring and whether the job is a repair or an installation. Fast dispatch runs from 7am to 7pm, Sunday through Friday.
2. 2
   On-site measurement and survey. We measure the actual opening, check slope and drainage, and inspect posts and footings. For automation we note gate weight and travel so the operator is matched to the panel. This is where most installation problems get caught before they cost money.
3. 3
   Written estimate before any work. You get a clear price for the job, including removal of the old gate where that’s part of it. Nothing starts until you’ve agreed to that estimate. The price is quoted and agreed up front, not adjusted after the fact.
4. 4
   Installation and commissioning. Posts go to proper footing depth, the gate is hung and checked for level travel, and the operator is fitted and programmed. Safety edges and photo eyes get tested on the closing path. We don’t call a gate done until it runs clean through full cycles.
5. 5
   Walkthrough and handover. We program remotes and keypads, show you how the gate operates, and leave you with the settings documented. If anything needs adjustment after the install, one call brings us back to gate repair kent and get it sorted.

How Much Does Gate Installation Cost in Kent?

Our Service Area Near Kent

We handle gate installation and repair across Kent and the surrounding area, including Lakeland North, Des Moines, Fairwood, Covington, SeaTac, Auburn, Lake Morton-Berrydale, Tukwila, and Federal Way. Response times depend on the job and the day, but dispatch runs from 7am to 7pm, Sunday through Friday, and installation work is scheduled around the measurement. If you’re in Lakeland North or Des Moines, the drive to your property is short, which keeps scheduling simple.

Frequently Asked Questions About Gate Installation in Kent

Schedule Your Gate Installation Service in Kent Today

If your gate needs replacing or automating, one call starts the process. We’ll measure the opening, recommend the right gate and operator, and give you a written price before anything begins. Our technicians have up to 12 years of experience and work on the brand already on your property. Call (855) 360-7358. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. The estimate is free and there’s no obligation.

Written by the team at Gate Repair Kent.