Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Motor & Opener Cost in Kent?
Replacing a residential swing gate opener in Kent typically runs $650 to $1,900 installed, while a sliding gate operator runs $1,100 to $3,200 installed. Commercial-grade operators from brands like FAAC, BFT, or DoorKing usually land between $2,200 and $6,500 depending on gate weight, cycle count, and access-control hardware. A written on-site estimate sets the final price, and we give that estimate for free.
Kent sits in the Green River Valley, where wet winters and heavy seasonal rain work on outdoor equipment year after year. Gate motors mounted low, drains that back up, and control boxes that take on water are common reasons a call comes in. Our technicians have up to 12 years of experience diagnosing exactly which part of the system failed, so you’re not paying to replace a whole operator when the actual fault is a limit switch or a water-logged control board.
We’re gate repair Kent specialists, which means every job on our schedule is a gate job. Residential or commercial, automated or manual, from the motor to the hinge. Call (855) 360-7358. We answer 24/7, and fast dispatch runs from 7am to 7pm.
Key Takeaways
- Residential swing gate opener replacement in Kent: $650 – $1,900 installed.
- Residential sliding gate operator: $1,100 – $3,200 installed.
- Commercial-grade operators (FAAC, BFT, DoorKing): $2,200 – $6,500 installed.
- Operator repair rather than replacement often costs $200 – $800.
- Estimates are free, and a technician comes out to price the actual job.
Gate Motor & Opener Cost Breakdown (2026)
Here’s how the numbers usually break down on a Kent gate job. These are typical estimated ranges for 2026, and every one is set by the written estimate after we’ve looked at your gate.
| Line Item | Typical Estimated Range |
|---|---|
| Diagnostic visit and estimate | Free |
| Operator repair (control board, limit switch, capacitor, arm) | $200 – $800 |
| Residential swing gate opener, supply and install | $650 – $1,900 |
| Residential sliding gate operator, supply and install | $1,100 – $3,200 |
| Commercial-grade swing or slide operator (FAAC, BFT, DoorKing) | $2,200 – $6,500 |
| Access-control add-ons (keypad, intercom, card reader integration) | $250 – $1,200 |
| Safety reversing devices and photo-eye sensors | $150 – $500 |
| Battery backup kit | $200 – $700 |
| Gate hardware refresh (hinges, rollers, tracks) | $150 – $600 |
| Manual-to-automatic conversion, labor and operator | $900 – $2,800 |
What pushes a job up or down? Gate weight and width matter a lot. A wide, heavy ornamental gate needs an operator sized for that load, and an undersized motor is one of the most common failures we see. Cycle count matters too: a home driveway gate opens a few times a day, while a commercial lot or HOA entrance can cycle hundreds of times, and that calls for a commercial-grade operator with a duty rating built for the traffic. Existing wiring, the type of gate (swing vs. slide), and access-control needs all move the number as well. If the gate structure itself is sound and only the motor or control board failed, you’re often in the repair range rather than the full-replacement range.
Brand familiarity keeps pricing honest. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so we already know the parts, the failure points, and the programming on the system that’s on your property.
What Affects Gate Motor & Opener Pricing in Kent
- Gate type and size. Sliding gates and wide swing gates need bigger operators, which cost more than a standard single-leaf residential swing.
- Residential vs. commercial duty. A commercial operator from FAAC, BFT, or DoorKing carries a higher price because it’s built to cycle far more often and hold up to heavier panels.
- Wet-weather exposure. The Green River Valley gets a lot of rain, and low-mounted motors and control enclosures that sit in a wet spot often need rethinking, not just a replacement part. Getting water away from the controls is part of the fix.
- Electrical access. If power needs to be run to an operator location, that adds labor. If power is already there, the job is simpler.
- Access control. Keypads, intercoms, card readers, and phone-based entry all add material and integration time to the job.
- Existing gate condition. Sagging hinges, worn rollers, or a bent track will burn out a new motor fast, so we price hardware repairs alongside the operator when the gate needs them.
One thing worth knowing about the property types we see around Kent: gated communities and HOA-managed entrances in the city’s newer residential developments often run commercial-grade operators because a shared entrance cycles far more than a private driveway. That difference in duty rating is usually the single biggest factor separating a $1,200 job from a $4,000 one.
How to Save on Gate Motor & Opener
You don’t need a coupon to keep costs down. The real savings come from catching problems early and sizing the operator correctly the first time.
- Get the operator sized right. An undersized motor on a heavy gate is the fastest way to spend twice. We match the operator to the actual gate weight and cycle count.
- Fix the gate structure before the motor. A gate that drags or sags stresses the motor on every cycle. Repairing hinges and rollers is cheaper than replacing burned-out operators.
- Keep water away from the controls. Given Kent’s winters, mounting control boxes where they drain and don’t pool water pays for itself. Ask about placement during the estimate.
- Consider repair over replacement when it makes sense. A failed control board or limit switch on an otherwise healthy operator is a repair job, not a replacement job.
- Add safety devices once. If you’re replacing an operator, installing photo-eye sensors and a battery backup at the same time is more economical than adding them later.
Every one of those decisions starts with a free estimate. A technician comes out, looks at your gate, and gives you a written price. Call (855) 360-7358. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Can You Repair a Gate Operator Instead of Replacing It?
Yes, often. Many operator failures come down to a single component: a control board, a limit switch, a capacitor, or a worn actuator arm. Repair typically runs $200 to $800 versus $650 to $1,900 for a new residential operator. A technician can tell you in one visit whether the motor itself is the problem or a part around it. If the equipment is a brand we know, like Linear or Elite or LiftMaster, we already know its failure points. That’s the value of working with specialists who handle Kent gate systems of every type. Call (855) 360-7358 for a free estimate.
Do Commercial Gate Operators Cost More in Kent?
Yes. Commercial-grade operators from FAAC, BFT, and DoorKing typically run $2,200 to $6,500 installed, compared with $650 to $1,900 for a residential swing opener. The difference is duty rating and build: a commercial operator is designed for heavy cycling, heavier gate panels, and access-control integration. For an HOA entrance or a commercial lot, that extra capacity is what prevents repeat failures. We service both residential brands like Ghost Controls and Mighty Mule and commercial systems, so the same specialist handles your property whatever its grade. Call (855) 360-7358.
How Long Does a Gate Motor Installation Take?
Most residential operator replacements are completed in a single visit, and many simpler repairs are done same-day. Larger commercial installations or manual-to-automatic conversions can take longer, depending on wiring and gate structure. When you call, we’ll talk through the scope and book a time that works. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening.
Can You Come the Same Day?
Same-day service is available, and we aim to get there fast for gates that are stuck open or shut. Because a gate motor failing can leave a driveway or entrance unsecured, we treat stuck gates as a priority. Fast dispatch runs from 7am to 7pm. Call (855) 360-7358 for a free estimate. We answer 24/7.
FAQs – Gate Motor & Opener Cost
How much does a new gate opener cost in Kent?
A new residential swing gate opener in Kent typically costs $650 to $1,900 installed, and a sliding gate operator runs $1,100 to $3,200 installed. Commercial-grade operators land between $2,200 and $6,500. The written estimate after an on-site look sets the final price. Call (855) 360-7358 for an exact quote; estimates are free.
Is it cheaper to repair or replace a gate motor?
Repair is usually cheaper when the fault is a single component: $200 to $800 versus $650 to $1,900 for a new residential operator. Replacement makes more sense when the motor itself is failing or the gate has outgrown an undersized operator. A technician can tell you which in one visit. Call (855) 360-7358 for a free estimate.
What does a commercial gate operator cost in Kent?
Commercial-grade operators from FAAC, BFT, and DoorKing typically cost $2,200 to $6,500 installed, depending on gate weight, cycle count, and access-control hardware. For HOAs and commercial properties, that duty rating is what keeps the entrance reliable. Call (855) 360-7358 for a free estimate.
How much does it cost to convert a manual gate to automatic in Kent?
Converting a manual gate to automatic typically runs $900 to $2,800, covering the operator and labor. Final cost depends on gate weight, whether power is already at the location, and any access-control add-ons. Call (855) 360-7358 for a free estimate.
Do you charge for a gate motor estimate in Kent?
No. Estimates are free, and the price is set per job by the written estimate. A technician comes out, assesses your gate and operator, and gives you a written range before any work begins. Call (855) 360-7358. We answer 24/7, with fast dispatch from 7am to 7pm.
Why a Gate Specialist for Your Motor and Opener
Gate motors and operators sit at the junction of mechanical and electrical work. An operator can fail because of a control board, a limit switch, a worn hinge, a dragging track, or water in the enclosure, and a generalist often guesses at which. A single-trade gate specialist diagnoses it. We work on nine major brands (LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule), we handle repair and full installation, and every job on our schedule is a gate job. If your operator is on its way out or already down, we get your gate back in service.
Have the brand and model of your operator ready when you call. That alone speeds up the diagnosis. Call (855) 360-7358 for a free estimate. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday.
Written by the team at Gate Repair Kent.
Pricing reflects the Kent market as of 2026. Gate Repair Kent offers free estimates – call (855) 360-7358.
What Our Customers Say
"Second time using them. Same guy, same good work."
- Eric Barrett"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Jennifer Whitaker"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Mark Norris