Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Access Control Cost in Kent?
Gate access control in Kent typically costs $450 to $1,800 for keypads, card readers and entry systems, with most residential keypad and remote jobs landing between $450 and $950. Full commercial access-control setups with card readers, intercom and telephone entry run $1,200 to $3,500 depending on the number of entry points. Every price is set per job by a written estimate, and estimates are free.
Access control is the part of a gate system that decides who gets in. The operator moves the gate, but the access control tells it when to open. On a residential driveway in Kent that might be a keypad and a pair of remotes. On a commercial lot or an HOA entrance it’s more likely a card reader, a telephone entry unit, a loop detector and a barrier that logs every entry. Those are very different jobs, and the prices reflect that.
We’re gate specialists, not generalists. We work on the brand already on your property, and we handle access control on both residential and commercial systems: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule. From the motor to the hinge, and from the keypad to the phone app, we diagnose the actual problem instead of guessing at it.
One thing we won’t do is quote a number that changes when a technician arrives. The written estimate is the price. If you want the exact figure for your gate, call (855) 360-7358. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- A basic residential keypad and remote setup in Kent runs roughly $450 to $950 installed.
- Commercial card readers, telephone entry and loop systems typically run $1,200 to $3,500.
- Adding access control to an existing gate often costs less than replacing a failed operator.
- Repairing a control board, receiver or keypad usually falls between $150 and $450.
- Brand familiarity matters. We service nine major gate and operator brands, so we’re not learning your system on your dime.
Gate Access Control Cost Breakdown (2026)
Here’s how the line items stack up for Kent properties. Treat these as typical ranges for the market, not a fixed quote. The written estimate is what sets the final price.
| Item | Typical Price Range |
|---|---|
| Residential keypad entry (wired or wireless) | $250 – $600 |
| Remote receiver and transmitter setup | $150 – $400 |
| Intercom or telephone entry unit (residential) | $450 – $1,200 |
| Commercial card reader and credential system | $800 – $2,000 |
| Telephone entry / directory unit (commercial) | $900 – $2,500 |
| Loop detector and vehicle sensor | $350 – $900 |
| Control board replacement | $200 – $550 |
| Keypad or receiver repair | $150 – $450 |
| Full access-control package (single entry, commercial) | $1,200 – $3,500 |
| Access control added during a new gate install | $400 – $1,500 |
What pushes a job toward the top of a range? Commercial-grade hardware, multiple entry points, integration with an existing DoorKing or FAAC system, and the wiring runs needed to reach a card reader in a location that doesn’t already have power. What keeps it low? A straightforward residential keypad swap on a gate whose operator and wiring are already healthy. In Kent, a lot of the access-control calls we get are actually a failing receiver or a keypad that’s taken on water, not a system that needs replacing. Diagnosing that correctly is the difference between a few hundred dollars and a few thousand.
What Affects Gate Access Control Pricing in Kent
- Residential vs. commercial grade. A Ghost Controls or Mighty Mule residential keypad setup is priced very differently from a DoorKing telephone entry unit in a commercial lot. The hardware, the credentialing, and the number of users all change the number.
- Brand on the property. We service nine major brands, which means we work on the system that’s already installed rather than selling you a whole new one. Where a generalist has to guess at a FAAC or BFT control board, we’ve handled that hardware before.
- Existing wiring and power. Adding a card reader to a post with no power nearby means trenching or routing new wire. That’s a real cost, and it’s the single biggest wildcard on access-control quotes.
- Number of entry points. One driveway on a residential property is not the same job as a commercial lot with a vehicle gate, a pedestrian gate and a delivery entrance. Each point needs its own reader or keypad, its own wiring and its own place on the controller.
- Weather and slope. Kent’s wet winters punish keypads and intercoms mounted where water pools or runs off a post cap. A slightly different mounting height or a better-sealed enclosure often costs a little more up front and saves a lot in callbacks. Gates on a slope also need the loop or sensor tuned to the approach, not just bolted on.
- Integration with the operator. Access control only helps if the operator responds to it. If the gate’s motor or control board is on its last legs, the access-control work has to account for that. We’d rather tell you that up front than after the fact.
How to Save on Gate Access Control
The best savings on an access-control job almost always come from fixing the actual fault instead of replacing parts that aren’t broken. A keypad that won’t work might be a dead keypad, or it might be a loose wire or a bad receiver. We test before we replace, and that’s where the money is.
- Get a diagnosis, not a sales pitch. If someone quotes you a full commercial system for a residential driveway keypad problem, ask why. A free estimate should tell you what’s actually wrong.
- Keep the brand you have. We’re familiar with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule. Staying with the existing brand usually means no rewiring and no reprogramming of every remote in the house or the HOA.
- Bundle access control with a repair or install. If your gate already needs a motor repair or a new installation, adding access control at the same time is cheaper than a separate visit. We handle repair, electric gate repair and installation under one roof, so it’s one project, not two.
- Ask about the wiring plan. On a commercial quote, ask where the wire will run and whether existing conduit can be reused. That single question can move a price by hundreds of dollars.
- Get the written estimate first. Ours is free, and it sets the price. Call (855) 360-7358 and we’ll take a look at what you’re running now.
If you’re starting from scratch with a new automated gate, it’s worth reading up on how the pieces fit together. Our gate repair Kent specialists walk through repair, electric gate repair and installation, and our Kent service information covers what local properties tend to need. Both are good places to understand the whole system before you decide on access control.
FAQs – Gate Access Control Cost
How much does a keypad entry system cost in Kent?
A residential keypad entry system in Kent typically runs $250 to $600 installed, with most jobs landing near the middle of that range. Wired keypads cost a bit more up front but hold up better through wet winters than wireless units. Call (855) 360-7358 for an exact quote. Estimates are free.
Is it cheaper to repair or replace an access-control system?
Repair is usually cheaper. A keypad or receiver repair typically runs $150 to $450, while a full commercial access-control package runs $1,200 to $3,500. The exception is when the hardware is obsolete or the wiring is failing at multiple points, where replacement makes more sense. A free estimate will tell you which side of that line you’re on. Call (855) 360-7358.
What does commercial gate access control cost in Kent?
Commercial gate access control in Kent usually costs $1,200 to $3,500 for a single entry point with a card reader, telephone entry or intercom, plus loop detection. Multi-entry commercial lots rank toward the top of that range or above. DoorKing and FAAC systems are common on commercial sites, and we service both. Call (855) 360-7358 for a scoped estimate.
Can you install access control on a gate you didn’t install?
Yes. We work on the brand already on your property, whether that’s LiftMaster, BFT, Linear, Viking, Elite, Mighty Mule or any of the others we handle. We diagnose the existing operator first, then recommend access control that matches it. If the operator itself needs repair, we can handle that at the same time. Call (855) 360-7358.
Can you come today?
Often, yes. Same-day service is available for many Kent access-control calls, and we answer the phone 24/7 with fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (855) 360-7358 to find out what’s available for your gate.
Why Brand Familiarity Changes the Price
Gate access control sits at the intersection of mechanics and electronics. The operator is a motor and a gearbox. The access control is a controller, a receiver, a keypad or a reader, and the wiring that ties them together. Getting the price right means knowing which part is actually failing.
That’s why we lead with the brand. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule. We’ve handled the residential-grade systems and the commercial-grade ones. When a DoorKing telephone entry unit stops dialing out, or a Ghost Controls keypad won’t take a code, we’re not reading the manual for the first time on your property. Our technicians have up to 12 years of experience, and every job is a gate job. No divided attention across unrelated trades.
It also means we can do the whole job. Repair, electric gate repair, and installation are all within our scope, so a new gate with access control is one project with one point of contact. We’re licensed and insured, we give upfront pricing, and the written estimate is the price.
Book a Free Access Control Estimate in Kent
If your gate’s access control isn’t working the way it should, or you’re planning a new system for a home, an HOA entrance or a commercial lot, the fastest way to a real number is a free estimate. We’ll look at the operator, the wiring and the access control together, because they only work as a system. Call (855) 360-7358. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Kent market as of 2026. Gate Repair Kent offers free estimates – call (855) 360-7358.
Written by the team at Gate Repair Kent.
What Our Customers Say
"Second time using them. Same guy, same good work."
- Eric Barrett"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Jennifer Whitaker"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Mark Norris